![]() “Flagrant” in these rules does not necessarily imply malice on the part of the fouling player or an intention to injure an opponent.Ĭopyright © 2023 by the National Football League. The word “flagrant,” when used here to describe an action by a player, is meant to indicate that the degree of a violation of the rules-usually a personal foul or unnecessary roughness-is extremely objectionable, conspicuous, unnecessary, avoidable, or gratuitous. It is not meant to connote illegality under any public law or the rules or regulations of any other organization. Where the word “illegal” appears in this rule book, it is an institutional term of art pertaining strictly to actions that violate NFL playing rules. Member clubs of the League may amend the rules from time to time, pursuant to the applicable voting procedures of the NFL Constitution and Bylaws.Īny intra-League dispute or call for interpretation in connection with these rules will be decided by the Commissioner of the League, whose ruling will be final.īecause inter-conference games are played throughout the preseason, regular season, and postseason in the NFL, all rules contained in this book apply uniformly to both the American and National Football Conferences. This edition of the Official Playing Rules of the National Football League contains all current rules governing the playing of professional football that are in effect for the 2023 NFL season. 15-1-2 | Expands the Replay Official’s jurisdiction to allow for automatic review of a turnover on downs after a failed fourth down attempt. ![]() Removes the “butt, ram or spear” language from Article 8 and incorporates those actions into the revised Impermissible Use of the Helmet article. 12-2-8 and 10 | Clarifies the Use of the Helmet rule.12-2-6 and 9 | Changes the definition of a launch from a player who “leaves both feet” to a player who “leaves one or both feet”.12-2-14 | Makes the penalty for tripping a personal foul (15 yards).10-2-4 | Puts the ball in play at the receiving team’s 25-yard line if there is a fair catch on a free kick behind the receiving team’s 25-yard line.9-1-1 | Makes the penalty for illegal punts, drop kicks, or placekicks a loss of down and five yards.8-7-4 | Makes the penalty for handing the ball forward to an ineligible receiver behind the line of scrimmage a loss of down and five yards.4-8-2 | Prevents the offense from benefitting by an extension of the half as a result of their foul.4-6-3 4-7-4 | Makes the adjustment of the play clock following an Instant Replay reversal consistent with other timing rules.Allows kickers and punters to use any jersey numeral between 0-49 and 90-99. 5-1-2 | Permits the use of zero (“0”) as a jersey numeral for certain positions.Lock the dizzy down and set the idle RPM back where you want it.Download a printable PDF of the 2023 NFL Rulebook. You use ZERO because your light is flashing 11 BTDC. Rotate the dizzy until the engine's ZERO marker lines up with the pointer. ![]() Press the FLASH button and the light/strobe should start. Using our example above, you would press INC until "11" is displayed. Switch to advance mode and use the DEC or INC buttons to change the time at which the light flashes. In tach mode bring the RPM up to 1000 using the idle speed adjustment screw. Let's say you want to SET the timing to 11 BTDC at 1000 RPM. What you do need to know is how to use the feature. you don't have to know the factory specs for your engine. To use the advance feature he mentioned above. ![]() To elaborate on the above, the black clip goes to an earth point, the red clip goes to +12V (the battery terminal on the starter solenoid is such a point) and the inductive pickup clamps onto the plug wire for cylinder #1. Use the same thing to check full advance. When you use the light set properly it will read zero degrees at the set rpm IF the timing is correct. Then switch to tach and adjust it to the correct number. Now use the Tach/Adv button to select degrees. and that full advance should be something like 30 degrees at 1500 rpms. They will tell you that base timing should be something like 4 degrees at 500 rpm. To use the advance feature you need the specs for the engine. Now it will display the rpms of the engine and can be used as a standard timing light. It should come up and ask you to select number of cylinders. Hook up the battery leads, Clip the pickup on cylinder number one. Flash - On/Off for the strobe Dec - Decrease the setting Inc - Increases the setting Basic use. Stole this from another site (where someone asked for a manual for the same model timing light), maybe it'll help you: Reset button - resets the light to zero Tach/Adv - Toggles between the tach setting and the advance settings. This is the best I could come up with after Googling for a while: Quoting from that site.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |